If you have been reading about Primary drying and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Updated 2025-09-26. Numbers and descriptions here follow the published literature rather than marketing material.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
Storage conditions depend on the formulation and the intended shelf life. Many pharmaceutical and biological freeze-dried products are kept at 2–8 °C, while some stable foods and reagents tolerate room temperature. Others require −20 °C or colder to slow chemical degradation or aggregation. Protection from light and oxygen is common because oxidation can continue in the dry state. Stability studies usually monitor potency, appearance, moisture, and reconstitution time over months or years. Predictions from accelerated studies are useful but may not fully capture real-time changes.
Quality control for freeze-dried lots combines visual inspection with instrumental tests. Cake appearance, color, and shrinkage are recorded against a reference, while residual moisture is measured by Karl Fischer titration or loss on drying. Thermal analysis can reveal phase transitions and crystallization events, and X-ray diffraction distinguishes amorphous from crystalline solids. Microbiological tests and container closure integrity checks are also routine for sterile products. Analytical methods must be validated for the matrix, because excipients and low moisture can affect accuracy. Open questions include how best to predict long-term stability from short-term data.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
Reconstitution involves adding a suitable diluent, often sterile water or a buffer, to the dried cake. Gentle swirling or inversion helps dissolve the material without creating excessive foam. The time required for complete dissolution can range from seconds to several minutes and depends on the cake structure and the diluent. Improper reconstitution, such as vigorous shaking or using the wrong diluent, can cause protein aggregation or loss of activity. After reconstitution, the product may have a limited shelf life and should be used according to its labeling.
Lyophilized products are typically hygroscopic and require protection from moisture during storage. Manufacturers seal them in glass vials, often under vacuum or an inert gas such as nitrogen. The container closure system, including the stopper and crimp seal, must prevent water vapor ingress. Storage temperature varies from controlled room temperature to refrigerated or frozen conditions, depending on the formulation. Humidity-controlled environments are essential because even brief exposure to ambient air can degrade the product.
Eq. 3 This means that coconut oil with an abundance of medium chain fatty acids (mainly lauric acid) contain more fatty acids per unit of weight than, for example, olive oil (mainly oleic acid). Consequently, more ester saponifiable functions were present per g of coconut oil, which means more KOH is required to saponify the same amount of matter, and thus a higher SV. The calculated molecular weight (Eq. 3) is not applicable to fats and oils containing high amounts of unsaponifiable material, free fatty acids (> 0.1%), or mono- and diacylglycerols (> 0.1%).
ADIME, or Assessment, Diagnosis, Intervention, and Monitoring/Evaluation, is a process used to ensure high quality nutrition care to patients and clients from nutrition professionals, such as Registered Dietitians (RD) or Registered Dietitian Nutritionist (RDN). ADIME is used as a means of charting patient progress and to encourage a universal language amongst nutrition professionals. The ADIME process consists of four steps:
The US Food and Drug Administration (FDA) approves anti-obesity medications as an adjunctive therapy to diet and exercise for people for whom lifestyle changes do not result in sufficient weight loss. In the United States, semaglutide (Wegovy) is approved by the FDA for chronic weight management. The FDA guidelines say that a therapy may be approved if it results in weight loss that is statistically significant greater than placebo and generally at least five percent of body weight over six months that comes predominantly from fat mass. Some other prescription weight loss medications are stimulants, which are recommended only for short-term use, and thus are of limited usefulness for patients who may need to reduce weight over months or years. As of 2022, there is no pathway for approval for drugs that reduce fat mass without 5 percent overall weight loss, even if they significantly improve metabolic health; neither is there one for drugs that help patients maintain weight loss although this can be more challenging than losing weight. As of 2022, no medication has been discovered that would equal the effectiveness of bariatric surgery for long-term weight loss and improved health outcomes.
About 1,500 heat-related deaths occurred in the Netherlands, again largely the elderly. The heat wave broke no records, although four tropical weather-designated days in mid-July, preceding the official wave, are not counted due to a cool day in between and the nature of the Netherlands specification/definition of a heat wave. The highest temperature recorded this heatwave was on 7 August, when in Arcen, in Limburg, a temperature of 37.8 °C (100.0 °F) was reached, 0.8 °C below the national record (since 1904). A higher temperature had only been recorded twice before. On 8 August, a temperature of 37.7 °C (99.9 °F) was recorded, and 12 August had a temperature of 37.2 °C (99.0 °F). Initially, 141 deaths were attributed to the heat wave in Spain. A further research of INE estimated a 12,963 excess of deaths during summer of 2003. Temperature records were broken in various cities, with the heat wave being more felt in typically cooler northern Spain. Record temperatures were felt in:
Sources: en.wikipedia.org
Because lipopolysaccharides are potent inflammatory agents, and the action of antibiotics can result in the release of these compounds, the binding capacity of BPI was explored as a possible means of reducing injury. Xoma Ltd. developed a recombinant 21kDa portion of the BPI molecule called rBPI21, NEUPREX, or opebecan. In a trial, it was found to decrease the mortality of Gram-negative bacterial-induced sepsis. Studies suggest that its binding activity is not the means by which it mediates its protective effect. Studies show biological effects with Gram-positive bacteria and even in infection by the protozoan, Toxoplasma gondii. The N-terminal portion of murine BPI (199 amino acids) genetically fused to Halobacterium sp. NRC-1 GvpC protein was bound to the surface of gas vesicle nanoparticles (GVNPs) and tested for protective activity using a murine model of endotoxic shock. Depending on the time of delivery and exposure to lethal concentrations of lipopolysaccharide (LPS) and D-galactosamine, the treatment resulted in increased survival and reduced symptoms of inflammation, including inflammatory anemia, recruitment of neutrophils, liver apoptosis as well as increased pro-inflammatory serum cytokine levels. When administered via footpad and before LPS exposure, there was 100% survival of the experimental cohort.
The core of comparative genome analysis is the establishment of the correspondence between genes (orthology analysis) or other genomic features in different organisms. Intergenomic maps are made to trace the evolutionary processes responsible for the divergence of two genomes. A multitude of evolutionary events acting at various organizational levels shape genome evolution. At the lowest level, point mutations affect individual nucleotides. At a higher level, large chromosomal segments undergo duplication, lateral transfer, inversion, transposition, deletion and insertion. Entire genomes are involved in processes of hybridization, polyploidization and endosymbiosis that lead to rapid speciation. The complexity of genome evolution poses many exciting challenges to developers of mathematical models and algorithms, who have recourse to a spectrum of algorithmic, statistical and mathematical techniques, ranging from exact, heuristics, fixed parameter and approximation algorithms for problems based on parsimony models to Markov chain Monte Carlo algorithms for Bayesian analysis of problems based on probabilistic models. Many of these studies are based on the detection of sequence homology to assign sequences to protein families.
The human ADM gene is localized to a single locus on Chromosome 11 with 4 exons and 3 introns. The ADM gene initially codes for a 185-amino acid precursor peptide, that can be differentially excised to form a number of peptides, including an inactive 53-amino acid AM, e PAMP, adrenotensin and ADM95-146. Mature human ADM is activated to form a 52-amino acid, 6-amino acid ring, that shares moderate structural similarity to the calcitonin family of regulatory peptides (calcitonin, CGRP and amylin). Circulating ADM consists of both the amidated active form (15%) and the glycated inactive form (85%). It has a plasma half-life of 22min, a mean clearance rate of 27.4 mL/kg/min, and an apparent volume of distribution of 880 ± 150 mL/kg. Adrenomedullin consists of 52 amino acids, has 1 intramolecular disulfide bond, and shows a slight homology with the calcitonin gene-related peptide (CGRP). The precursor, called preproadrenomedullin, consists of 185 amino acids and can be cleaved by plasma kallikrein at the Lys-Arg and Arg-Arg sites. By RNA-blot analysis, human adrenomedullin mRNA was found to be expressed in all tissues, and most highly expressed in the placenta, fat cells, lung, pancreatic islets, smooth muscle, and skin.
A chromogranin A-derived antifungal peptide (CGA 47–66, chromofungin) when embedded on a surface has been shown to have antifungal activity by interacting with the fungal membrane and thereby penetrating the cell. Additionally, in vitro studies have demonstrated that such an antifungal coating can inhibit the growth of yeast Candida albicans by 65% and completely stop the proliferation of filamentous fungus Neurospora crassa. Copper and copper alloy surfaces have demonstrated a die-off of Aspergillus spp., Fusarium spp., Penicillium chrysogenum, Aspergillus niger and Candida albicans fungal spores. Hence, the potential to help prevent the spread of fungi that cause human infections by using copper alloys (instead of non-antifungal metals) in air conditioning systems is worthy of further investigation. The physical topology of a surface will determine the viable environment for bacteria. It may affect a microbe's ability to adhere to its surface. Textile surfaces tend to be very easy for microbes to adhere to due to the abundance of interstitial spacing between fibers.
The main method of treatment for potential death from signaling-related diseases involves either increasing or decreasing the susceptibility of apoptosis in diseased cells, depending on whether the disease is caused by either the inhibition of or excess apoptosis. For instance, treatments aim to restore apoptosis to treat diseases with deficient cell death and to increase the apoptotic threshold to treat diseases involved with excessive cell death. To stimulate apoptosis, one can increase the number of death receptor ligands (such as TNF or TRAIL), antagonize the anti-apoptotic Bcl-2 pathway, or introduce Smac mimetics to inhibit the inhibitor (IAPs). The addition of agents such as Herceptin, Iressa, or Gleevec works to stop cells from cycling and causes apoptosis activation by blocking growth and survival signaling further upstream. Finally, adding p53-MDM2 complexes displaces p53 and activates the p53 pathway, leading to cell cycle arrest and apoptosis. Many different methods can be used either to stimulate or to inhibit apoptosis in various places along the death signaling pathway. Apoptosis is a multi-step, multi-pathway cell-death programme that is inherent in every cell of the body. In cancer, the apoptosis cell-division ratio is altered. Cancer treatment by chemotherapy and irradiation kills target cells primarily by inducing apoptosis.
Sources: en.wikipedia.org
Caddisfly silk is silk that is secreted by the silk glands of the caddisfly (Trichoptera), similar to Lepidoptera silkworms (B. mori). The larvae use silk to hunt and defend themselves. The silk's underwater binding properties are a subject of ongoing scientific research. Trichoptera, or caddisfly, larvae use silk to hunt and protect themselves in their aquatic environment. Much like silkworms and other Lepidoptera, this silk protein is excreted by specialized silk glands. The silk’s structure is mostly conserved among many different caddisfly species, and can be used to bind debris including rocks, sticks, twigs and shells, as well as to build nets for catching prey. Caddisflies, which spend the majority of their life cycle in the larval stage, need these casings to protect their underbellies and pupate. Caddisfly silk is very strong and durable. Because their silk must be able to bind to a variety of components while completely submerged in water, it is therefore being studied for potential applications as a waterproof adhesive.
Before amylin deposition was associated with diabetes, already in 1901, scientists described the phenomenon of "islet hyalinization", which could be found in some cases of diabetes. A thorough study of this phenomenon was possible much later. In 1986, the isolation of an aggregate from an insulin-producing tumor was successful, a protein called IAP (Insulinoma Amyloid Peptide) was characterized, and amyloids were isolated from the pancreas of a diabetic patient, but the isolated material was not sufficient for full characterization. This was achieved only a year later by two research teams whose research was a continuation of the work from 1986.
Chondrocytes (, from Greek χόνδρος (chondros) 'cartilage' and κύτος (kytos) 'cell') are the only cells found in healthy cartilage. They produce and maintain the cartilaginous matrix, which consists mainly of collagen and proteoglycans. Although the word chondroblast is commonly used to describe an immature chondrocyte, the term is imprecise, since the progenitor of chondrocytes (which are mesenchymal stem cells) can differentiate into various cell types, including osteoblasts. From least- to terminally-differentiated, the chondrocytic lineage is:
Coiled-coil α helices are highly stable forms in which two or more helices wrap around each other in a "supercoil" structure. Coiled coils contain a highly characteristic sequence motif known as a heptad repeat, in which the motif repeats itself every seven residues along the sequence (amino acid residues, not DNA base-pairs). The first and especially the fourth residues (known as the a and d positions) are almost always hydrophobic; the fourth residue is typically leucine – this gives rise to the name of the structural motif called a leucine zipper, which is a type of coiled-coil. These hydrophobic residues pack together in the interior of the helix bundle. In general, the fifth and seventh residues (the e and g positions) have opposing charges and form a salt bridge stabilized by electrostatic interactions. Fibrous proteins such as keratin or the "stalks" of myosin or kinesin often adopt coiled-coil structures, as do several dimerizing proteins. A pair of coiled-coils – a four-helix bundle – is a very common structural motif in proteins. For example, it occurs in human growth hormone and several varieties of cytochrome. The Rop protein, which promotes plasmid replication in bacteria, is an interesting case in which a single polypeptide forms a coiled-coil and two monomers assemble to form a four-helix bundle.
Class A (or 1) (Rhodopsin-like) Class B (or 2) (Secretin receptor family) Class C (or 3) (Metabotropic glutamate/pheromone) Class D (or 4) (Fungal mating pheromone receptors) Class E (or 5) (Cyclic AMP receptors) Class F (or 6) (Frizzled/Smoothened) More recently, an alternative classification system called GRAFS (Glutamate, Rhodopsin, Adhesion, Frizzled/Taste2, Secretin) has been proposed for vertebrate GPCRs. They correspond to classical classes C, A, B2, F, and B. An early study based on available DNA sequence suggested that the human genome encodes roughly 750 G protein-coupled receptors, about 350 of which detect hormones, growth factors, and other endogenous ligands. Approximately 150 of the GPCRs found in the human genome have unknown functions. Some web-servers and bioinformatics prediction methods have been used for predicting the classification of GPCRs according to their amino acid sequence alone, by means of the pseudo amino acid composition approach. GPCRs are involved in a wide variety of physiological processes. Some examples of their physiological roles include:
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
Karl Fischer titration is widely used because it is specific for water and works at low levels. Loss on drying is simpler but less specific, since volatile solvents or decomposition products can also be lost.