If you have been reading about sublimation and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-02-10. Where a claim depends on a specific study, the study is described rather than over-claimed.
A formulation often contains excipients that protect the active ingredient during freezing and drying. Bulking agents provide structure, while lyoprotectants stabilize sensitive molecules. The freezing step can produce ice crystals whose size and distribution affect the drying rate, and cycle design includes freezing, annealing, and drying phases. If the product temperature rises above a critical value, the cake may collapse or lose its porous structure. Successful lyophilization therefore depends on the interaction between formulation, equipment, and cycle design.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilization is the American spelling; lyophilisation is British |
| Primary drying mechanism | Sublimation of ice | Occurs under vacuum below the triple point |
| Typical chamber pressure | 0.05-0.5 mbar | Range depends on product and equipment |
| Typical shelf temperature during freezing | -40 to -20 °C | Lower temperatures may be used for labile products |
| Resulting product form | Porous cake or powder | Appearance depends on formulation and cycle |
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Lyophilization, also called freeze-drying, removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts free water into ice and may also produce a glassy phase. Primary drying then lowers chamber pressure so ice sublimes directly to vapor without passing through a liquid stage. Secondary drying raises the temperature modestly to remove bound water. The result is a porous, dry solid that usually reconstitutes quickly. Each stage influences pore structure, residual moisture, and stability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
The full-length human protein comprises 2,843 amino acids with a (predicted) molecular mass of 311646 Da. Several N-terminal domains have been structurally elucidated in unique atomistic high-resolution complex structures. Most of the protein is predicted to be intrinsically disordered. It is not known if this large predicted unstructured region from amino acid 800 to 2843 persists in vivo or would form stabilised complexes – possibly with yet unidentified interacting proteins. Recently, it has been experimentally confirmed that the mutation cluster region around the center of APC is intrinsically disordered in vitro.
Evolutionary biology is a subfield of biology that analyzes the mechanisms of evolution. Evolution accounts for the unity and diversity of life on Earth; Theodosius Dobzhansky famously said "nothing in biology makes sense except in the light of evolution". Population genetics for example studies how genetic variation develops, how it is inherited, and how the evolutionary mechanisms shape a population's genetic composition. Research in evolutionary biology covers many topics and incorporates ideas from diverse areas, such as molecular genetics and mathematical and theoretical biology. Some fields of evolutionary research try to explain phenomena that were poorly accounted for in the modern evolutionary synthesis. These include speciation, the evolution of sexual reproduction, the evolution of cooperation, the evolution of ageing, and evolvability. Ecology is the study of the distribution and abundance of life, the interaction between organisms and their environment.
Binding sites can be characterized also by their structural features. Single-chain sites (of "monodesmic" ligands, μόνος: single, δεσμός: binding) are formed by a single protein chain, while multi-chain sites (of "polydesmic" ligands, πολοί: many) are frequent in protein complexes, and are formed by ligands that bind more than one protein chain, typically in or near protein interfaces. Recent research shows that binding site structure has profound consequences for the biology of protein complexes (evolution of function, allostery).
Absorption spectroscopy is spectroscopy that involves techniques that measure the absorption of electromagnetic radiation, as a function of frequency or wavelength, due to its interaction with a sample. The sample absorbs energy, i.e., photons, from the radiating field. The intensity of the absorption varies as a function of frequency, and this variation is the absorption spectrum. Absorption spectroscopy is performed across the electromagnetic spectrum. Absorption spectroscopy is employed as an analytical chemistry tool to determine the presence of a particular substance in a sample and, in many cases, to quantify the amount of the substance present. Infrared and ultraviolet–visible spectroscopy are particularly common in analytical applications. Absorption spectroscopy is also employed in studies of molecular and atomic physics, astronomical spectroscopy and remote sensing. There is a wide range of experimental approaches for measuring absorption spectra. The most common arrangement is to direct a generated beam of radiation at a sample and detect the intensity of the radiation that passes through it. The transmitted energy can be used to calculate the absorption. The source, sample arrangement and detection technique vary significantly depending on the frequency range and the purpose of the experiment. Following are the major types of absorption spectroscopy:
Sources: en.wikipedia.org
Amyloid is formed through the polymerization of hundreds to thousands of monomeric peptides or proteins into long fibers. Amyloid formation involves a lag phase (also called nucleation phase), an exponential phase (also called growth phase) and a plateau phase (also called saturation phase), as shown in the figure. When the quantity of fibrils is plotted versus time, a sigmoidal time course is observed reflecting the three distinct phases. In the simplest model of 'nucleated polymerization' (marked by red arrows in the figure below), individual unfolded or partially unfolded polypeptide chains (monomers) convert into a nucleus (monomer or oligomer) via a thermodynamically unfavourable process that occurs early in the lag phase. Fibrils grow subsequently from these nuclei through the addition of monomers in the exponential phase. A different model, called 'nucleated conformational conversion' and marked by blue arrows in the figure below, was introduced later on to fit some experimental observations: monomers have often been found to convert rapidly into misfolded and highly disorganized oligomers distinct from nuclei. Only later on, will these aggregates reorganise structurally into nuclei, on which other disorganised oligomers will add and reorganise through a templating or induced-fit mechanism (this 'nucleated conformational conversion' model), eventually forming fibrils.
Even with all the precautions taken by medical professionals, infection reportedly occurs in up to 13.9% of patients after stabilization of an open fracture, and in about 0.5-2% of patients who receive joint prostheses. To reduce these numbers, the surfaces of the devices used in these procedures have been altered in hopes of preventing the growth of the bacteria that leads to these infections. This has been achieved by coating titanium devices with an antiseptic combination of chlorhexidine and chloroxylenol. This antiseptic combination successfully prevents the growth of the five main organisms that cause medical-related infections, which include Staphylococcus epidermidis, Methicillin-resistant Staphylococcus aureus, Pseudomonas aeruginosa, Escherichia coli and Candida albicans. Peptide-based gel coating with intrinsic antibacterial activity against Methicillin-resistant Staphylococcus aureus, was also shown to inhibit colonization of titanium implants in mice.
In order to regulate the secretion of ACTH, many substances secreted within this axis exhibit slow/intermediate and fast feedback-loop activity. Glucocorticoids secreted from the adrenal cortex work to inhibit CRH secretion by the hypothalamus, which in turn decreases anterior pituitary secretion of ACTH. Glucocorticoids may also inhibit the rates of POMC gene transcription and peptide synthesis. The latter is an example of a slow feedback loop, which works on the order of hours to days, whereas the former works on the order of minutes. The half-life of ACTH in human blood is reported to be between ten and 30 minutes. ACTH consists of 39 amino acids, the first 13 of which (counting from the N-terminus) may be cleaved to form α-melanocyte-stimulating hormones (α-MSH) (this common structure is responsible for excessively tanned skin in Addison's disease). After a short period of time, ACTH is cleaved into α-melanocyte-stimulating hormone (α-MSH) and CLIP, a peptide with unknown activity in humans. In the human body, total weight ACTH is 4540 Da.
While juxtaposed against free-radical polymerization, the application of automated synthesis can be utilized for controlled radical polymerization too. These methods have been used within reversible addition-fragmentation transfer (RAFT), atom-transfer radical (ATRP), and nitroxide-mediated polymerizations, demonstrating the ability of robots to improve efficiency and reduce the hardship of performing reactions. For example, with the automatic dispensation of reagents, Symyx Technologies Inc. was able to polymerize styrene and butyl acrylate through ATRP. In addition, this functionality was supported by Zhang et al. within their research, finding that reproducibility and comparability were equivalent to classical ATRP.
Polycondensation involves the formation of polymers through condensation reactions between different species, creating condensation polymers. With automated synthesis, General electric manufactured an approach for melt-polymerizations of BPA and diphenyl carbonate (DPC), using sodium hydroxide (NaOH) as the catalyst. Once the results were analyzed, it was shown that, by using an automated method of polymerization, the effect of varying the catalyst amount became more distinct and improved the reproducibility for the reaction. Furthermore, it demonstrated an increase within the homogeneity of the polymers in the microreactors.
Sources: en.wikipedia.org
Alloxan is a toxic glucose analogue, which selectively destroys insulin-producing cells in the pancreas (that is, beta cells) when administered to rodents and many other animal species. This causes an insulin-dependent diabetes mellitus (called "alloxan diabetes") in these animals, with characteristics similar to type 1 diabetes in humans. Alloxan is selectively toxic to insulin-producing pancreatic beta cells because it preferentially accumulates in beta cells through uptake via the GLUT2 glucose transporter. Studies suggest alloxan does not cause diabetes in humans. Others found a significant difference in alloxan plasma levels in children with and without type 1 diabetes. Alloxan (C4H2N2O4) readily undergoes redox cycling with its one-electron (C4H3N2O4• semiquinone) and two-electron (dialuric acid, C4H4N2O4) reduction products. In the presence of intracellular reductants such as glutathione (or other thiols), this leads to the generation of toxic reactive oxygen species (ROS) via the interaction of alloxan reduction products with molecular oxygen and related species:
Another common example is the reaction of a primary amine or secondary amine with a carboxylic acid or with a carboxylic acid derivative to form an amide. This reaction is widely used, especially in the synthesis of peptides. On the simple addition of an amine to a carboxylic acid, a salt of the organic acid and base is obtained. To overcome this, the carboxylic acid first needs to be "activated". This is usually done by converting the acid into a more reactive derivative (i.e. anhydride, acid halide) or by using a coupling agent. In some cases, high temperatures (>200 °C) can overcome salt formation by driving off water, without the need for "activation" of the carboxyl group. The downside to this simple reaction is that the compounds may decompose at these elevated temperatures. The carboxylic acid derivatives can be esters, anhydrides, acid halides or any other activated species. The choice of activated carboxyl group or coupling agent can be very important in peptide synthesis, as using the wrong one can lead to racemization.
Automated iterative homologation enables stepwise construction of carbon chains through repeated one-carbon extensions of boronic esters. Two reactions adapted to automation are the Matteson homologation, which inserts a methylene unit via chloromethyllithium, and chiral carbenoid homologation, which uses lithiated benzoate esters. Both methods have been implemented on robotic platforms under low-temperature, inert conditions. Using these techniques, up to six consecutive C(sp³)–C(sp³) bond-forming homologations have been performed without manual intervention, representing the highest number reported in an automated synthesis. The approach has also been applied to the synthesis of intermediates of the natural product (+)-kalkitoxin.
The Hmd holoenzyme includes the protein homodimer as well as its associated iron-containing cofactor. Several species of methanogens have been characterized that express enzymes in the Hmd hydrogenase family. Between species the enzyme is found with differing numbers of sub-units and some minor amino acid sequence variations. The monomer is approximately 45,000 Da in mass, although this value varies from species to species. The enzymatic activity of the enzyme is lost upon exposure to sunlight or UV. Photolysis causes the release of an iron atom and two molecules of carbon monoxide. In the holoenzyme the Fe and CO molecules are found associated with a 542 Da cofactor.
The protein is 82.3 kDa and has a 40 amino acid long LEM domain located at its amino-terminal region. In its carboxyl end it has a RNA recognition motif (RRM). The LEM domain is also common to two other integral proteins of the INM: lamina-associated polypeptide 2 (LAP2) and emerin. The LEM segment enables LEMD3 to attach to the barrier-to-autointegration factor (BAF), and therefore, indirectly interact with the chromatin. LEMD3 also has several implications in regulating the cytokine family such as the transforming growth factor beta (TGF-β) and bone morphogenic protein (BMPs). The RRM domain in its carboxylic region attaches to the SMAD (protein) proteins, which is involved in mediating TGF-β cellular signalling. Consequently, LEMD3 indirectly regulates downstream genes. LEMD3 seems to play an important role in regulating the expression of several fundamental genes. LEMD3 has been associated with laminopathies as well as osteopoikilosis. Mutations in the LEMD3 gene have been linked to several genetic diseases such as osteopoikilosis, melorheostosis and Buschke–Ollendorff syndrome.
Sources: en.wikipedia.org
Lyophilization removes water by sublimation from a frozen material, while evaporation changes liquid water into vapor. The low-pressure freezing step avoids the liquid phase and can preserve heat-sensitive structures.
Vacuum lowers the pressure below the triple point of water, allowing ice to sublimate directly into vapor. It also helps remove water vapor from the product chamber and shortens primary drying.
Many aqueous solutions and suspensions can be freeze-dried, but some formulations collapse or do not form a stable cake. The process requires careful formulation and cycle development.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.