Primary drying raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-03-07 and is reviewed periodically as new material appears.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
Stability of a lyophilized solid depends on water content, temperature, and the physical state of the formulation. Amorphous products may slowly absorb moisture and drop below their glass transition temperature, causing collapse or crystallization. Some proteins and peptides can aggregate even in a dry state, especially when exposed to heat or moisture. Accelerated stability studies at elevated temperature and humidity help estimate shelf life, but real-time data remain the basis for expiration dating.
After drying, a lyophilized product is usually sealed under vacuum or an inert gas to limit moisture and oxygen exposure. The container closure system matters because stoppers and seals can allow moisture ingress over time. Storage conditions are selected from stability studies that track potency, cake appearance, and reconstitution behavior. Many freeze-dried materials are kept at controlled room temperature, while some require refrigeration or protection from light.
| Property | Value | Notes |
|---|---|---|
| Common name | Freeze-drying | Process removes water by sublimation under vacuum. |
| Typical primary drying shelf temperature | -40 C to -10 C | Set below the formulation's collapse temperature. |
| Typical chamber pressure | 0.05-0.3 mbar | Low pressure allows ice to sublime below its triple point. |
| Water content after drying | 0.5-3% by weight | Higher values may reduce storage stability for some materials. |
| Key thermal parameter | Collapse temperature | Measured by freeze-drying microscopy or differential scanning calorimetry. |
A typical cycle begins with freezing, which fixes the material into a solid and determines ice crystal size. Primary drying then raises heat under vacuum so ice sublimes, often near or below the collapse temperature of the formulation. Secondary drying removes bound water that remains after ice is gone, usually by gently warming the product. Each stage balances heat input against pressure to avoid melting or structural damage. Temperature probes and pressure sensors guide the transition between stages.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
After lyophilization, the dried product is often sealed under vacuum or an inert gas to limit moisture and oxygen exposure. Vials, stoppers, and seals must maintain their barrier throughout shelf life. Storage temperature depends on product sensitivity: some cakes tolerate controlled room temperature, while labile biologics require refrigeration. Humidity is a critical variable because dried cakes are hygroscopic and can absorb water when exposed to air. Handling procedures therefore limit open-vial time and use desiccated environments for sampling.
Quality control for lyophilized materials examines appearance, reconstitution time, residual moisture, and mechanical integrity. An acceptable cake is usually uniform and porous, though appearance alone does not prove stability. Karl Fischer titration is a common method for water content, while differential scanning calorimetry can reveal glass transition events. Stability studies track potency, aggregation, and moisture over time under defined temperature and humidity conditions. Specifications are product-specific and may include sterility and endotoxin tests for sterile preparations.
The main building of the Institute is located at the intersection of Kremlyovskaya and Lobachevskaya streets. This four-story building built in 1953 in the style of Soviet neoclassicism under the guidance of architect A.G. Bikchentaev. The building of the museum of Kazan chemical school is located in the campus of the main university building, built in the 1830s in a classical style under the guidance of architect M.P. Corinfskiy. In 2015 construction of a large laboratory building in the campus of Alexander Butlerov Institute of Chemistry was finished. The 7-storey building housed classrooms and laboratories of departments of Alexander Butlerov Institute of Chemistry, Institute of Geology and Petroleum Technologies, Institute of Physics. The building was constructed with the support of the President of Tatarstan R.N. Minnikhanov and PSC "TAIF".
H3O+(aq) + Cl−(aq) + NH3 → Cl−(aq) + NH+4(aq) + H2O HCl(benzene) + NH3(benzene) → NH4Cl(s) HCl(g) + NH3(g) → NH4Cl(s) As with the acetic acid reactions, both definitions work for the first example, where water is the solvent and hydronium ion is formed by the HCl solute. The next two reactions do not involve the formation of ions but are still proton-transfer reactions. In the second reaction hydrogen chloride and ammonia (dissolved in benzene) react to form solid ammonium chloride in a benzene solvent and in the third gaseous HCl and NH3 combine to form the solid.
Absorption spectroscopy is spectroscopy that involves techniques that measure the absorption of electromagnetic radiation, as a function of frequency or wavelength, due to its interaction with a sample. The sample absorbs energy, i.e., photons, from the radiating field. The intensity of the absorption varies as a function of frequency, and this variation is the absorption spectrum. Absorption spectroscopy is performed across the electromagnetic spectrum. Absorption spectroscopy is employed as an analytical chemistry tool to determine the presence of a particular substance in a sample and, in many cases, to quantify the amount of the substance present. Infrared and ultraviolet–visible spectroscopy are particularly common in analytical applications. Absorption spectroscopy is also employed in studies of molecular and atomic physics, astronomical spectroscopy and remote sensing. There is a wide range of experimental approaches for measuring absorption spectra. The most common arrangement is to direct a generated beam of radiation at a sample and detect the intensity of the radiation that passes through it. The transmitted energy can be used to calculate the absorption. The source, sample arrangement and detection technique vary significantly depending on the frequency range and the purpose of the experiment. Following are the major types of absorption spectroscopy:
Helices observed in proteins can range from four to over forty residues long, but a typical helix contains about ten amino acids (about three turns). In general, short polypeptides do not exhibit much α-helical structure in solution, since the entropic cost associated with the folding of the polypeptide chain is not compensated for by a sufficient amount of stabilizing interactions. In general, the backbone hydrogen bonds of α-helices are considered slightly weaker than those found in β-sheets, and are readily attacked by the ambient water molecules. However, in more hydrophobic environments such as the plasma membrane, or in the presence of co-solvents such as trifluoroethanol (TFE), or isolated from solvent in the gas phase, oligopeptides readily adopt stable α-helical structure. Furthermore, crosslinks can be incorporated into peptides to conformationally stabilize helical folds. Crosslinks stabilize the helical state by entropically destabilizing the unfolded state and by removing enthalpically stabilized "decoy" folds that compete with the fully helical state. It has been shown that α-helices are more stable, robust to mutations and designable than β-strands in natural proteins, and also in artificially designed proteins.
Many different inventions and ideas which may or may not have been practical about auto safety have been put forward but never made it to a production car. Such items include the driver seat in the middle (to give the person a better view) (the exception being the McLaren F1 super car) and control stick steering. Automotive safety may have become an issue almost from the beginning of mechanised road vehicle development. The second steam-powered "Fardier" (artillery tractor), created by Nicolas-Joseph Cugnot in 1771, is reported by some to have crashed into a wall during its demonstration run. However, according to Georges Ageon, the earliest mention of this occurrence dates from 1801 and it does not feature in contemporary accounts. One of the earliest recorded car-related fatalities was Mary Ward, on August 31, 1869, in Parsonstown, Ireland. In 1922, the Duesenburg Model A became the first car to have four-wheel hydraulic brakes.
Sources: en.wikipedia.org
The amino acids in an α-helix are arranged in a right-handed helical structure where each amino acid residue corresponds to a 100° turn in the helix (i.e., the helix has 3.6 residues per turn), and a translation of 1.5 Å (0.15 nm) along the helical axis. Dunitz describes how Pauling's first article on the theme in fact shows a left-handed helix, the enantiomer of the true structure. Short pieces of left-handed helix sometimes occur with a large content of achiral glycine amino acids, but are unfavorable for the other normal, biological L-amino acids. The pitch of the alpha-helix (the vertical distance between consecutive turns of the helix) is 5.4 Å (0.54 nm), which is the product of 1.5 and 3.6. The most important thing is that the N-H group of one amino acid forms a hydrogen bond with the C=O group of the amino acid four residues earlier; this repeated i + 4 → i hydrogen bonding is the most prominent characteristic of an α-helix. Official international nomenclature specifies two ways of defining α-helices, rule 6.2 in terms of repeating φ, ψ torsion angles (see below) and rule 6.3 in terms of the combined pattern of pitch and hydrogen bonding. The α-helices can be identified in protein structure using several computational methods, such as DSSP (Define Secondary Structure of Protein).
The terms "active" and "passive" are simple but important terms in the world of automotive safety. "Active safety" is used to refer to technology assisting in the prevention of a crash and "passive safety" to components of the vehicle (primarily airbags, seatbelts and the physical structure of the vehicle) that help to protect occupants during a crash. Crash avoidance systems and devices help the driver — and, increasingly, help the vehicle itself — to avoid a collision. This category includes: The vehicle's headlamps, reflectors, and other lights and signals The vehicle's mirrors The vehicle's brakes, steering, and suspension systems A subset of crash avoidance is driver assistance systems, which help the driver to detect obstacles and to control the vehicle. Driver assistance systems include:
Bodybuilding supplements are dietary supplements commonly used by those involved in bodybuilding, weightlifting, mixed martial arts, and athletics for the purpose of facilitating an increase in lean body mass. Bodybuilding supplements may contain ingredients that are advertised to increase a person's muscle, body weight, athletic performance, and decrease a person's percent body fat for desired muscle definition. Among the most widely used are high protein drinks, pre-workout blends and caffeinated energy drinks, branched-chain amino acids (BCAA), glutamine, arginine, essential fatty acids, creatine, HMB, whey protein, ZMA, and weight loss products. Supplements are sold either as single ingredient preparations or in the form of "stacks" – proprietary blends of various supplements marketed as offering synergistic advantages.
A number of AlphaFold clones have also been published, mostly with permissive license terms. Clones for AlphaFold3 include ByteDance's Protenix (Apache 2.0 License), AlQuraishi Laboratory's OpenFold-3 (MIT license), and Boltz-1/2 (MIT license). There are also clones for older versions, though they became less relevant with the open-source release of AlphaFold 1 and 2 source codes. Still relevant are models, both open- and closed-source, that include modifications to the AlphaFold architecture. For AlphaFold 2, a notable example is ESMFold from Meta, which replaces the multiple sequence alignment with the latent space of a protein language model. Open-source tools that complement AlphaFold have also been made. One well-cited example is ColabFold, which uses MMseqs2 instead of HHblits to speed up the sequence search, allowing the AlphaFold pipelines to run quickly on Google Colab.
Sources: en.wikipedia.org
The main method of treatment for potential death from signaling-related diseases involves either increasing or decreasing the susceptibility of apoptosis in diseased cells, depending on whether the disease is caused by either the inhibition of or excess apoptosis. For instance, treatments aim to restore apoptosis to treat diseases with deficient cell death and to increase the apoptotic threshold to treat diseases involved with excessive cell death. To stimulate apoptosis, one can increase the number of death receptor ligands (such as TNF or TRAIL), antagonize the anti-apoptotic Bcl-2 pathway, or introduce Smac mimetics to inhibit the inhibitor (IAPs). The addition of agents such as Herceptin, Iressa, or Gleevec works to stop cells from cycling and causes apoptosis activation by blocking growth and survival signaling further upstream. Finally, adding p53-MDM2 complexes displaces p53 and activates the p53 pathway, leading to cell cycle arrest and apoptosis. Many different methods can be used either to stimulate or to inhibit apoptosis in various places along the death signaling pathway. Apoptosis is a multi-step, multi-pathway cell-death programme that is inherent in every cell of the body. In cancer, the apoptosis cell-division ratio is altered. Cancer treatment by chemotherapy and irradiation kills target cells primarily by inducing apoptosis.
The sequence of GVPa is extremely well conserved. GvpJ and gvpM, two proteins encoded in the cluster of genes required for gas vesicle synthesis in the archaebacteria Halobacterium salinarium and Halobacterium mediterranei (Haloferax mediterranei), have been found to be evolutionarily related to GVPa. The exact function of these two proteins is not known, although they could be important for determining the shape determination gas vesicles. The N-terminal domain of Aphanizomenon flos-aquae protein gvpA/J is also related to GVPa. GvpA of Halobacterium salinarum is a 76 amino acid long 8 kDa hydrophobic monomer. Gas vesicles are hollow cylindrical tubes, closed by a hollow, conical cap at each end. Both the conical end caps and central cylinder are made up of 4-5 nm wide ribs that run at right angles to the long axis of the structure. Gas vesicles seem to be constituted of two different protein components, GVPa and GVPc. GVPa, a small protein of about 70 amino acid residues, is the main constituent of gas vesicles and form the essential core of the structure.
The area under the effect curve (AUEC) is an integral of the effect of a drug over time, estimated as a previously-established function of concentration. It was proposed to be used instead of AUC in animal-to-human dose translation, as computer simulation shows that it could cope better with half-life and dosing schedule variations than AUC. This is an example of a PK/PD model, which combines pharmacokinetics and pharmacodynamics. Cmax (pharmacology) Cmean (pharmacology) "Area Under Curve" of the Receiver operating characteristic
Sources: en.wikipedia.org
Primary drying removes ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, often under the same vacuum. The two stages differ in the water state being removed.
Freezing determines ice crystal size, pore structure, and the concentration of solutes in remaining liquid. Faster freezing generally creates smaller ice crystals and a denser dried matrix. These features affect drying rate and reconstitution behavior.
Lyophilization reduces water content but usually leaves a small amount of water in the dried material. Some water remains bound to solids or trapped in the dried matrix. Very low water targets can require extended secondary drying, which may alter product stability.
Sealed vials or containers should be kept at the temperature specified by stability data, often controlled room temperature or 2–8 °C. Moisture and oxygen barriers are important because both can degrade sensitive materials. Opened containers may need immediate use or protection from ambient humidity.