Primary drying comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2026-03-21. Where a claim depends on a specific study, the study is described rather than over-claimed.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen so that water becomes ice; then the surrounding pressure is lowered below the vapor pressure of ice. Heat is applied gently so ice changes directly to vapor without passing through a bulk liquid phase. The vapor is collected on a cold condenser, leaving a dry porous matrix. This process differs from simple evaporation because the material remains frozen during the main drying stage.
The process usually has three stages: freezing, primary drying, and secondary drying. Freezing sets the ice crystal structure and can determine pore size in the final cake. Primary drying removes free ice by sublimation at low pressure and low shelf temperature. Secondary drying removes bound water by raising the shelf temperature, although some water may remain as part of the solid. Cycle parameters depend on formulation, fill volume, vial type, and equipment performance.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
Freeze-drying is distinct from simple evaporation and from spray drying. Evaporation removes water at temperatures above freezing, while spray drying rapidly dries droplets in a heated gas stream. Lyophilization avoids high temperatures, which can be useful for heat-sensitive materials such as proteins, vaccines, and some foods. The porous cake produced by sublimation dissolves or rehydrates more quickly than a dense dried mass. Not all materials tolerate freezing or the pH shifts that can occur as solutes concentrate during ice formation.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | Freeze-drying, lyophilisation | Lyophilisation is the British spelling; the process is not simple evaporation. |
| Primary drying pressure | 0.05–0.3 mbar | Pressure must remain below the vapor pressure of ice at the product temperature. |
| Sublimation temperature | Below 0 °C | Ice changes directly to vapor while the product remains frozen. |
| Typical shelf temperature | −40 to −10 °C | Exact setting depends on formulation critical temperature and equipment. |
| Cycle duration | 12–72 hours | Time varies with fill volume, formulation, and dryer performance. |
Equipment for lyophilization includes a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. A refrigeration system cools the shelves and condenser below the product's freezing point. Process monitoring often uses Pirani and capacitance manometers, thermocouples, and resistance sensors. Cycle development balances product quality with time and energy use. Some products are annealed during freezing to improve crystallization of bulking agents. Open questions remain about scaling cycles between laboratory, pilot, and production freeze-dryers.
Lyophilization, also called freeze-drying, removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts free water into ice and may also produce a glassy phase. Primary drying then lowers chamber pressure so ice sublimes directly to vapor without passing through a liquid stage. Secondary drying raises the temperature modestly to remove bound water. The result is a porous, dry solid that usually reconstitutes quickly. Each stage influences pore structure, residual moisture, and stability.
The physics of lyophilization depends on phase boundaries and heat and mass transfer. During primary drying, heat supplied to the product must equal the latent heat of sublimation, while water vapor moves through the drying cake to the condenser. If shelf temperature or pressure is set too high, the ice front can exceed the collapse temperature, causing meltback or pore collapse. If conditions are too cold, drying slows and costs rise. Formulation excipients, vial geometry, and freezing rate alter these limits.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and concentrates dissolved solids. Primary drying then lowers chamber pressure so ice changes directly into vapor without passing through a liquid phase. Secondary drying raises the shelf temperature to remove bound water that remains after ice sublimation. The result is a dry, porous structure that can be reconstituted later.
The tertiary structure and topology of TMEM125 was predicted and visualized through Phyre2. TMEM125 has 1 predicted phosphorylation site (CK2 Phos), 5 predicted N-myristoylation sites (N-myr), 2 predicted palmitoylation sites (Pal), and 1 predicted amidation site (Amid). It also contains the domain of unknown function 66 (DUF66). TMEM125 is predicted to be subcellularly localized in the plasma membrane. It is secondarily predicted to be localized in the endoplasmic reticulum. There were no scientifically-verified protein interactions identified for TMEM125. String Protein Interaction predicted 10 functional protein partners for TMEM125, but all were determined through textmining. TMEM125 is conserved in species as distantly related to humans as cartilaginous fish, that’s most recent common ancestor to humans existed 465 million years ago. TMEM125 is highly conserved in primates, mammals, birds, reptiles, bony fish, and cartilaginous fish, but is not observed in invertebrates. TMEM125 does not have any paralogs.
Acta Biochimica et Biophysica Sinica was a Chinese-language journal entitled "Shengwu Huaxue Yu Shengwu Wuli Xuebao" (see box below), which began publishing sometime in 1958 or 1959, or August 1961, until December 2003 (depending on the source). Tables of contents were in English. Summaries (abstracts) were in English and Russian, and text of articles in Chinese. Later issues were promulgated in the Chinese and English languages. The translated title was "Journal of Biochemistry and Biophysics". The frequency was quarterly from 1959 to 1963, bimonthly from 1964 to 2002, and finally, monthly by 2003. Publication was suspended from 1966 to 1975. It was indexed in Chemical Abstracts Service. It may have published 35 volumes in total, over the years. In 2004 the journal switched to a full English-language journal under its current title. Official website Institute of Biochemistry and Cell Biology Archived 2003-12-17 at the Wayback Machine, SIBS, CAS
When measured by fatalities per person transported, however, buses are the safest form of transportation. The number of air travel fatalities per person are surpassed only by bicycles and motorcycles. This statistic is used by the insurance industry when calculating insurance rates for air travel. For every billion kilometers traveled, trains have a fatality rate that is 12 times higher than that of air travel, and the fatality rate for automobiles is 62 times greater than for air travel. By contrast, for every billion journeys taken, buses are the safest form of transportation; using this measure, air travel is three times more dangerous than car transportation, and almost 30 times more dangerous than travelling by bus. A 2007 study by Popular Mechanics magazine found that passengers sitting at the back of an aeroplane are 40% more likely to survive a crash than those sitting at the front. The article quotes Boeing, the FAA, and a website on aircraft safety, all of which claim that there is no "safest" seat. The study examined 20 crashes, not taking into account the developments in safety after those accidents. However, a flight data recorder is usually mounted in the aircraft's empennage (tail section) where it is more likely to survive a severe crash. Between 1983 and 2000, the survival rate for people in U.S. plane crashes was greater than 95 percent.
2-Oleoylglycerol (2OG) is a monoacylglycerol that is found in biologic tissues. Its synthesis is derived from diacylglycerol precursors. It is metabolized to oleic acid and glycerol primarily by the enzyme monoacylglycerol lipase (MAGL). In 2011, 2OG was found to be an endogenous ligand to GPR119. 2OG has been shown to increase glucagon-like peptide-1 (GLP-1) and gastric inhibitory polypeptide (GIP) levels following administration to the small intestine. 2OG has also been discovered to potentiate G protein and not β-arrestin signaling via allosteric binding of the 5-HT2A receptor. 2-Arachidonoylglycerol JZL184
Sources: en.wikipedia.org
Amino acid-based formula is a type of infant milk formula made from individual amino acids. It is hypoallergenic and intended for infants suffering from severe allergy to milk and various gastrointestinal conditions, such as food protein-induced enterocolitis syndrome and malabsorption syndromes. It is sometimes referred to as elemental formula but this is considered a misleading name. Issues with the use of amino acid-based formula include its high cost and its unpalatable taste. Intake of amino-acid formula for healthy infants shows no advantage in growth.
Founded in 1984, Bio-Synthesis, Inc. was known as OCS Laboratories and was one of the first companies providing commercially available synthetic oligonucleotides to the biomedical research community worldwide. It was the first producer of commercially available synthetic DNA and became a producer of synthetic peptides in 1985, and became the only company to provide both synthetic DNA and peptide under one roof. Also in 1985 the process, now known as PCR, was discovered by Mullis et al. A key activity for Bio-Synthesis was to synthesize large number of PCR primer thus assisting and solidifying the early adoption of this now common and crucial process in biology.
Generally speaking single-particle measurement instruments desorb particles one at a time using a pulsed laser. The process is called laser desorption/ionization (LDI) and is the primary ionization method used for single-particle measurements. The main advantage of using LDI over thermal desorption, is the ability to analyze both non-refractory and refractory (e.g., mineral dust, soot) components of atmospheric aerosols. Laser vaporization allows precise laser firing when individual particles fly through the vaporization zone, and the systems are thus dubbed single particle mass spectrometers (SPMS). Several versions of SPMS have been reported, including the aerosol time-of-flight mass spectrometer (AToFMS), the laser mass analyzer for particles in the airborne state (LAMPAS), particle analysis by laser mass spectrometer (PALMS), the rapid single-particle mass spectrometer (RSMS), the bioaerosol mass spectrometer (BAMS) b194 Steele et al., 2003), the nanoaerosol mass spectrometer (NAMS), the single-particle laser ablation time-of-flight mass spectrometer (SPLAT), the single-particle aerosol mass spectrometer (SPAMS), and laser ablation aerosol particle time-of-flight mass spectrometer (LAAP-ToF-MS). Among the most commons of these instruments is the aerosol time-of-flight mass spectrometer (AToFMS).
Viral induction of apoptosis occurs when one or several cells of a living organism are infected with a virus, leading to cell death. Cell death in organisms is necessary for the normal development of cells and the cell cycle maturation. It is also important in maintaining the regular functions and activities of cells. Viruses can trigger apoptosis of infected cells via a range of mechanisms including:
Integrator complex subunit 15, also known as C7orf26, is a protein encoded in humans by the INTS15 gene. Based on properties of c7orf26 and its conservation over a long period of time, its suggested function is targeted for the cytoplasm and it is predicted to play a role in regulating transcription. Chromosome 7 is one of the 23 pairs of chromosomes in the human body, and spans about 159 million base pairs and represents about 5-5.5% of the total DNA in cells. Changes to the structure of chromosome 7 can result in a number of genetic abnormalities, including Williams Syndrome which causes structural and cosmetic changes to the human body, ultimately resulting in a shorter lifespan. There are hundreds of known open reading frames (ORF) along the domain of chromosome 7, however there is not much known about the 26th reading frame, which is of considerable interest. Currently, two isoforms of c7orf26 are known in Homo Sapiens and are referred to as isoforms 1 and 2, respectively.
Sources: en.wikipedia.org
Antidotes can be employed to either mop up hazardous metabolites or change them into less toxic forms once they have developed. Hepatic glutathione stores are replenished by N-acetyl cysteine, and this process is what leads to the conjugation of the poisonous metabolite N-acetyl P-benzoquinone imine (NAPQI). Receptor antagonist Receptor Dose–response relationship Pharmacodynamics Antidotes
Anti-obesity medication or weight loss medications are pharmacological agents that reduce excess body fat and cause weight loss. These medications alter one of the fundamental processes of weight regulation, by: reducing appetite and consequently energy intake, increasing energy expenditure, redirecting nutrients from adipose to lean tissue, or interfering with the absorption of calories. Weight loss drugs have been developed since the early twentieth century, and many have been banned or withdrawn from the market due to adverse effects, including deaths; other drugs proved ineffective. Although many earlier drugs were stimulants such as amphetamines, in the early 2020s, GLP-1 receptor agonists became popular for weight loss. As of 2023, the medications liraglutide, naltrexone/bupropion, orlistat, semaglutide, tirzepatide and phentermine/topiramate are approved by the US Food and Drug Administration (FDA) for weight management in combination with reduced-calorie diet and increased physical activity. Medications to treat obesity may be considered in those with a body mass index above 30, or above 27 with obesity related complications (such as hypertension, hyperlipidemia, cardiovascular disease, or obstructive sleep apnea). As of 2022, no medication has been shown to be as effective at long-term weight reduction as bariatric surgery.
Antibody–drug conjugates or ADCs are a class of bioconjugates and immunoconjugates. ADCs are composed of an antibody linked to a cytotoxic (anticancer) "payload" or drug. Among treatment options for cancer, chemotherapy is most widely used. Its main limitation is low target specificity. Unlike chemotherapy, ADCs target tumor cells while sparing healthy cells. As of 2019, some 56 pharmaceutical companies were developing ADCs. ADCs combine the targeting properties of monoclonal antibodies with the cancer-killing capabilities of cytotoxic drugs, designed to discriminate between healthy and diseased tissue.
General guidelines for diagnosing prolactin excess (hyperprolactinemia) define the upper threshold of normal prolactin at 25 μg/L for women and 20 μg/L for men. Similarly, guidelines for diagnosing prolactin deficiency (hypoprolactinemia) are defined as prolactin levels below 3 μg/L in women and 5 μg/L in men. However, different assays and methods for measuring prolactin are employed by different laboratories and as such the serum reference range for prolactin is often determined by the laboratory performing the measurement. Furthermore, prolactin levels vary according to factors as age, sex, menstrual cycle stage and pregnancy. The circumstances surrounding a given prolactin measurement (assay, patient condition, etc.) must therefore be considered before the measurement can be accurately interpreted. The following chart illustrates the variations seen in normal prolactin measurements across different populations. Prolactin values were obtained from specific control groups of varying sizes using the IMMULITE assay.
The society publishes three research journals and a review journal: the Journal of Pharmacology and Experimental Therapeutics, Drug Metabolism and Disposition, Molecular Pharmacology, and Pharmacological Reviews Starting in 2012 these publications are only offered online. The society copublishes a wholly open access journal with the British Pharmacological Society and Wiley entitled Pharmacology Research & Perspectives. ASPET also publishes a quarterly newsletter, The Pharmacologist, and, from 2001 to 2011, Molecular Interventions magazine. The society gives out several awards:
Sources: en.wikipedia.org
The main change is sublimation, in which ice becomes water vapor without melting into liquid water. This occurs when the chamber pressure is held below the vapor pressure of ice while mild heat is supplied. The result is a dry, porous solid that retains much of its original shape.
Freezing determines ice crystal size, solute distribution, and the pore network left after drying. A slow or fast freezing rate can produce different cake structures and affect reconstitution. It also sets whether the formulation follows an amorphous or crystalline drying path.
It removes most free water during primary drying and part of the bound water during secondary drying. A small residual moisture content often remains and is specified for each product. Complete removal is generally neither practical nor desirable for stability.
Lyophilization relies on sublimation, so water moves from solid ice to vapor without becoming liquid. The material is frozen, pressure is reduced, and controlled heat is supplied. Vapor is captured on a cold condenser, leaving a dry porous solid.